Comments 0 Comments
Tags ,

Having explored a range of suitable adhesives for the modern (and maybe not quite so modern) workshop, it’s time to look at a few ways of applying the stuff and more importantly, getting the ‘squeeze out’ off again. There’s a whole raft of different ways of applying adhesives, all of which work (depending on the job in question) very well to a greater or lesser extent.

The disadvantage of these systems is that most of them, unless designed to be disposable, need cleaning afterwards, which for me would be just another irksome chore to do at the end of a complex gluing process. There are a couple of exceptions which are much easier to clean and that’s the two applicators made from silicon rubber where the glue peels off when completely dry…except with polyurethane as noted by one or two customers in their reviews.

For many years I used the plastic spatulas which I usually bought in bulk from a local art shop, but even then, the services of a craft knife had to be employed to remove the dried glue, with the result that they soon became quite mangled and only fit for the bin.

I discovered quite by chance that a simple artist’s paintbrush is absolutely perfect for applying small quantities of glue as all I need to do is to drop it into a pot of water when I’ve finished, which then stops the stuff from setting. Being a parsimonious soul, I also discovered at about the same time that beechwood coffee stirring sticks work equally as well, with the advantage that they can be thrown away after use. Both of these methods work very well for many gluing applications such as dowels, dominoes, mortice and tenon joints, dovetails or similar.

glues_and_gluing_part_three_02

Occasionally, there’s a need to apply very small amounts of glue in precise locations and for that, the craft knife is again pressed into service to sharpen the end a coffee stirrer. The other option is to use a bamboo barbecue skewer and once the residual glue has been wiped off, it’s simply re-sharpened on the disc sander ready for another small gluing job.

Stanley Knife

Big areas, as may be found when veneering, need a different approach. Even a larger paint brush won’t get enough glue on quickly enough, so in this instance, a roller is the right tool for the job. I use a small decorator’s roller with a disposable foam head; the sort of thing used for painting behind radiators. I can buy a pack of ten of these things for less than £3 which doesn’t make too much of a dent the wallet!

glues_and_gluing_part_three_05
Applying the glue is fine, but how much should you slather on, if at all?

With the proviso that joints fit, the answer is the minimum to do the job properly and to ensure complete coverage of all surfaces, I always apply a thin smear of glue to both sides of the joint. There are different views on this as some woodworkers only apply glue to one surface, but if the ‘belt ‘n’ braces’ approach is adopted, you can be reasonably sure that that you’ve obtained the best coverage. The difficulty then arises because the time taken to apply the glue has now doubled, which means that the ‘open time’ has been halved and in a very warm workshop it’s a difficult call to make, especially if you’re using PVA!

Having gone through the tedious process of applying the glue and bringing the joint(s) together, you then need to remove any excess (before it sets solid) that escapes…the ‘squeeze out.’
Or do you?

One technique I frequently use is to pre-polish and wax all internal surfaces to provide a ‘resist’. When the glue has hardened to a jelly like constituency, it’s then easy to pick it off at leisure with the edge or point of a ‘shop made glue scraper, made from an oddment of acrylic plastic which is ground to shape at each end on the disc sander. When it becomes encrusted with glue, simply sand it again at each end to leave a pair of bevelled edges. This is especially useful with Cascamite which is very difficult to remove once it has set glass hard.

glues_and_gluing_part_three_01

When the ‘squeeze out’ has to be removed while it’s still wet, (for example, the inside of an unpolished drawer), the glue scraper is very effective at taking off most of the excess. What little remains can be completely removed by scrubbing the area with a stencil brush, (or a cut down glue brush) which has been dipped in clean water and the excess removed using a piece of rag so that it’s just damp; never wet, or the water will penetrate the joint and dilute the glue.

glues_and_gluing_part_three_04

This concludes this three part treatise on Glues and Gluing, but if you have any queries on the issue, please don’t hesitate to leave your questions below.

buying-guides-iconclockfirst-look-icongoogleplushow-tos-iconinsights-iconinstagrammeet-icontagwhats-on-icon